You have no items in your shopping cart.

Sorry - this product is no longer available

Exo-Lord Bionic Rifle Arms x 5 Pairs - LAST FEW!

£4.60
SKU: A-A-BR5
+ -

These are the last remaining sets that we have, when they're gone they're gone!

 

Five different pairs of Medium Bionic Rifle Arms.

Each pair is a different pose, and the set includes a pair with additional power/coolant cabling. These are designed for use with ourExo-Lord miniatures, and work well with other similarly sized 28mm miniatures.

Assembly Notes

  • We strongly reccomend that the parts be dry fitted together with blue tac to check for alignment.
  • We've found it easiest to glue the right arm on first, then blue tack the left arm in place and glue the rifle to the right arm, checking it sits correctly in the left hand and lines up right, then once the gun is secure, remove the left arm and glue it back in place.

Designed for use with Exo-Lords, these arms fit with our range of shoulder pads, or also look great used just by themselves without a pad.

This product is not a toy, it is  supplied unpainted, and will require some preparation and gluing with superglue. For further guidance, the Anvil Industry guide “Working with Resin” can be found at the bottom of the page.

Not a toy.Suitable for ages 14+

Not a toy.
Nije igračka.
Není to hračka.
Ikke et legetøj.
Geen speelgoed.
Ei ole mänguasi.
Ei lelu.
Pas un jouet.
Kein Spielzeug.
Όχι ένα παιχνίδι.
Nem játék.
Ní bréagán.
Non è un giocattolo.
Nav rotaļlieta.
Ne žaislas.
Mhux ġugarell.
Ikke et leketøy.
To nie jest zabawka.
Não é um brinquedo.
Nu o jucărie.
Ni igrača.
No es un juguete.
Inte en leksak.
Не е играчка.
Net e Spillsaach.

 

Product info


Please read the full product safety information and instructions here: https://anvilindustry.co.uk/product-info

 

 

General Safety Warnings


Anvil Industry products are miniature-scale collectibles, they are not toys, and are only suitable for ages 14+.

They should be kept out of reach of children aged 0-3 years as small parts may be sharp or a choking hazard.

All packaging should be kept out of reach of children aged 0-3 due to the risk of choking or suffocation.

Packaging should be disposed of in accordance with local legislation: Cardboard boxes and paper tape are recylable, void fill is startch based and compostable, gripseal bags are made from Polythene (LDPE) and are reusable and recyleable (please check with your local facility).


Product Materials

Note: Bundle products, like squad builders, may contain a mix of the following materials, please check the paperwork supplied with your order for the SKU of individual components.

Polyurethane Polymer (referred to as “Resin” or “Cast Resin”)

This material applies to all product SKUs beginning with "PU".

(Note: prior to 2025, sku's did not have the "PU" prefix.)

Products manufactured in the UK by Anvil Industry, using raw materials from the EU.

Appearance is grey in colour, hard and slightly flexible.

Material is non-hazourdous under normal conditions when fully cured, as shipped to customer.

Material is non-recyclable, and should be disposed of in general waste.


Photopolymer (referred to as “Resin” or “Printed Resin” or “3D Printed”)

This material applies to all SKUs beginning with “XX-3DP” where X's are numbers.

Products manufactured in the UK by Anvil Industry, using raw materials from China.

Appearance is grey in colour, hard and slightly flexible.

Material is non-hazourdous under normal conditions when fully cured, as shipped to customer.

Material is non-recyclable, and should be disposed of in general waste.


ABS Thermoplastic (referred to as “plastic”)

This material applies to all SKUs beginning with “BASE”.

Products manufactured in the EU by a supplier.

Appearance is black in colour, hard and slightly flexible.

Material is non-hazourdous at room temperature, as shipped to customer.

Material is recyclable along with other ABS plastics.

These are the last remaining sets that we have, when they're gone they're gone!

 

Five different pairs of Medium Bionic Rifle Arms.

Each pair is a different pose, and the set includes a pair with additional power/coolant cabling. These are designed for use with ourExo-Lord miniatures, and work well with other similarly sized 28mm miniatures.

Assembly Notes

  • We strongly reccomend that the parts be dry fitted together with blue tac to check for alignment.
  • We've found it easiest to glue the right arm on first, then blue tack the left arm in place and glue the rifle to the right arm, checking it sits correctly in the left hand and lines up right, then once the gun is secure, remove the left arm and glue it back in place.

Designed for use with Exo-Lords, these arms fit with our range of shoulder pads, or also look great used just by themselves without a pad.

This product is not a toy, it is  supplied unpainted, and will require some preparation and gluing with superglue. For further guidance, the Anvil Industry guide “Working with Resin” can be found at the bottom of the page.